Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
  RegisterRegister  LoginLogin
General Discussion
 Harmony : General Discussion
Subject Topic: Failed TM13 Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
bikerlad26
Senior Member
Senior Member
Avatar

Joined: 20 April 2008
Location: United Kingdom
Online Status: Offline
Posts: 786
Posted: 04 August 2013 at 5:08pm | IP Logged Quote bikerlad26

Hi All just a bit of advice

i have had a TM13 fail and had 2 MS13 (pir's) that connected to it which then
turned on 3 LM15's.

my question is while i am waiting for a new TM13 how can i still have the
lights coming on and off when the pir is activated

Thanks

Chris
Back to Top View bikerlad26's Profile Search for other posts by bikerlad26
 
Rob Iles
Admin Group
Admin Group
Avatar

Joined: 10 August 2005
Location: United Kingdom
Online Status: Offline
Posts: 5377
Posted: 04 August 2013 at 5:16pm | IP Logged Quote Rob Iles

I'd say "you can't", at least not without
additional hardware & configuration.....
Which only makes sense if you're going to
be waiting a long time for the TM13.

If the latter is the case, I'll post some
ideas.

R.
Back to Top View Rob Iles's Profile Search for other posts by Rob Iles Visit Rob Iles's Homepage
 
bikerlad26
Senior Member
Senior Member
Avatar

Joined: 20 April 2008
Location: United Kingdom
Online Status: Offline
Posts: 786
Posted: 04 August 2013 at 5:31pm | IP Logged Quote bikerlad26

Cheers Rob

I did think that was the case just thought someone might had some ideas

TM13 i should be getting at the end of the month
Back to Top View bikerlad26's Profile Search for other posts by bikerlad26
 
Rob Iles
Admin Group
Admin Group
Avatar

Joined: 10 August 2005
Location: United Kingdom
Online Status: Offline
Posts: 5377
Posted: 04 August 2013 at 5:51pm | IP Logged Quote Rob Iles

Bbs PIR's
Back to Top View Rob Iles's Profile Search for other posts by Rob Iles Visit Rob Iles's Homepage
 
Rob Iles
Admin Group
Admin Group
Avatar

Joined: 10 August 2005
Location: United Kingdom
Online Status: Offline
Posts: 5377
Posted: 04 August 2013 at 5:51pm | IP Logged Quote Rob Iles

I have a couple of bbs pic's in stock. You
could replace the ms13's with these, and
have Harmony switch the x10 lamps when it
hears the bbs signal...
Back to Top View Rob Iles's Profile Search for other posts by Rob Iles Visit Rob Iles's Homepage
 
bikerlad26
Senior Member
Senior Member
Avatar

Joined: 20 April 2008
Location: United Kingdom
Online Status: Offline
Posts: 786
Posted: 04 August 2013 at 6:20pm | IP Logged Quote bikerlad26

I do have a bbs PIR somewhere never thought of that

guessing just set up a fake device and get harmony to switch that on and
create an event to then turn the x10 lamps on
Back to Top View bikerlad26's Profile Search for other posts by bikerlad26
 
Rob Iles
Admin Group
Admin Group
Avatar

Joined: 10 August 2005
Location: United Kingdom
Online Status: Offline
Posts: 5377
Posted: 04 August 2013 at 6:39pm | IP Logged Quote Rob Iles

Create a device for the pir (using correct
address, make it a switch/socket).

Event 1: pir on, turn on x10 device

Event 2: pir off, turn off x10 device.

Back to Top View Rob Iles's Profile Search for other posts by Rob Iles Visit Rob Iles's Homepage
 
bikerlad26
Senior Member
Senior Member
Avatar

Joined: 20 April 2008
Location: United Kingdom
Online Status: Offline
Posts: 786
Posted: 04 August 2013 at 7:03pm | IP Logged Quote bikerlad26

Cheers Rob

Its been a while since i used the BBSB PIR remind me ML or YC mode can't
remember what the difference is

Chris
Back to Top View bikerlad26's Profile Search for other posts by bikerlad26
 
Rob Iles
Admin Group
Admin Group
Avatar

Joined: 10 August 2005
Location: United Kingdom
Online Status: Offline
Posts: 5377
Posted: 04 August 2013 at 7:11pm | IP Logged Quote Rob Iles

I use YC mode. The other does light level
detection IIRC.
Back to Top View Rob Iles's Profile Search for other posts by Rob Iles Visit Rob Iles's Homepage
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum